Citrix receiver for 10.7.5 mac osx. GE FANUC controls use a serial port to transfer data between the control and a computer or other device. J cole 2014 forest hills drive zip. There are a number of reasons why the communications would not be working properly. This document details the basic steps of troubleshooting the problem and finding a solution.
Fanuc Programming Manual Pdf
Fanuc Handy File manual Dear all. I have handy file box but i have not any file manual. Thanks, 09:28 AM #2. View Profile View Forum. (1) FANUC PPR (2) FANUC BUBBLE CASSETTE (3) FANUC FLOPPY CASSETTE (4) FANUC PROGRAM FILE (5) FANUC PROGRAM FILE Mate (6) FANUC Handy File Hereafter, the destination where the remote buffer is connected to be called “Host computer” for ease of explanation. With the Program Transfer Tool users can define communications between a PC and up to 255 FANUC CNC controls. The built-in Setting Dialog application aids in setup and initial communication testing. Each machine setting automatically opens the PC folder when communication is started so that the user does not have to hunt for the proper PC. This manual covers the specifications and the instructions and operations used for programming with the following devices. Product name Applicable CNC FANUC PMC-MODEL SD7 (PMC-SD7) FANUC Series 16i-MODEL B (Series 16i-B) FANUC Series 160i-MODEL B (Series 160i-B) FANUC Series 18i-MODEL B (Series 18i-B).
Gta romania 2 mediafire. PROCEDURE If no data is being input/output or serial port alarms are occurring.
Check the cable for proper connections. See Cable section below for cable diagram. Connect your computer up directly to the machine to eliminate cable junctions, switchboxes, etc.
Try communicating in the opposite direction than the one you are currently having trouble with.
Anaglyph.ax for km player. If you are having trouble with down/uploading on the PMC side try down/uploading on the CNC side (or vice-versa).
If you have a Fanuc communications device such as a Floppy Cassette or a Handy File, try to communicate to the CNC using it's standard setup.
Check your computer or other device by using it to communicate to another control, if available.
Make sure that the sending and receiving devices are set to the same baud rate, parity, stop bits and device type.
Insert an RS-232 tester (readily available from electronic stores for less than £15) into the line to check signal conditions. If not available, use a meter. See testing section below.
RS232 CONNECTIONS Check your cable against the following diagrams. RS232 is limited to communicating at distances of < 50 Ft. For testing purposes connect a short cable directly from the computer to the machine.
TESTING The RS232 breakout box is connected inline with the cable to monitor the communications signals. It has about 10 tristate LED's which monitor the signal lines indicating one color for positive voltage, another for negative and off for 0V.
The following chart indicates the LED states for the listed conditions. The box is plugged is inserted on the control side of the cable.
S1
S2
S3
SD
Toggling
Neg
Neg
RD
Neg
Toggling
Neg
RS, CS
Pos
Pos
Neg
DR, CD, ER
Pos
Pos
Neg
S1
Control Downloading Properly
S2
Control Uploading Properly
S3
Power up state or after DR OFF alarm occurred
If any of the signals are 0V or at the incorrect level this indicates a problem with the device controlling that signal. When the breakout box is inserted between the cable and the CNC then SD, RS, CS, DR, CD, ER are controlled by the CNC and RD is controlled by the computer. If it was inserted between the computer and the cable then the exact opposite is true.
If you are using a meter then the Positive level is 8.5 Volts and the Negative level is -8.5 Volts from the control. Android phone pattern unlock software for pc. Your computer should be emitting similar voltages.
NOTE: On all Fanuc controls, pin 25 of the RS-232 port is supplied with +24v from the control for use with specific GE Fanuc devices (ex. Cheat drivers ed. Handy File). DO NOT connect this pin through to your PC or it may be damaged
Instruction Manual and User Guide for Fanuc. We have 655 Fanuc manuals for free PDF download.
